--------------------------------------------------------
Note Before Usage:
1. Wht Is Not Date Displayed After I Installed It?
After the first installation, all data will be displayed after driving for 5-10 minutes. The sensor needs motion activation.
2. The Measurement Error?
The error value of measuring tire pressure is ±3PSI.
3. If The Tire Leak When Sensors Are Installed?
1) Actually, when the sensor is installed on your valve stem, it is normal to have some air leakage (as long as it does not cause the tire to leak suddenly). And over a period, tires may lose pressure naturally, through the tire itself or for other reasons such as rim leakage, etc. If you want to ensure as much as possible to reduce air leakage after the sensor is installed, the O-ring may helps with this. And I suggest you try the following methods: After installing the sensors on a tire valve stem, it is recommended to perform a soapy water test using 1/4 dish soap and 3/4 water. Spray the soapy solution on the valve stem and sensor area to ensure the sensor is seated all the way. If air bubbles are seen in any of these areas, the tire may deflate.
2) The Schrader Valve (core - inside the valve stem) should be the correct size, be in good condition and be able to be depressed fully to allow the release of air to the sensor so it can operate. Should you have difficulty with a pressure sensor not working properly, we recommend that you contact a tire professional to ensure that the tire stem and Schrader Valve are installed and operating properly. If using internal tire sealants or balancing compounds/beads check with the manufacturer to ensure they are compatible with TPMS systems or that you have filtered valve cores installed.
4. If The Sensor Data Do Not Displayed?
In the first installation, please turn on the monitor before installing the sensor on the tire. Please do not install the sensor on the tire before turning on the monitor. This operation may cause problems such as sensor data not being displayed and the monitor showing garbled characters. If you have installed the sensor on the tire first, please start your vehicle immediately and observe whether there is data displayed after 5-10 minutes. If there is still no data displayed, please remove the sensor and let it rest for 10 minutes before proceeding to the correct installation sequence.
If the sensor data disappear in your usage, please try these tips:
1. Remove the sensor and observe whether there is an alarm. If there is an alarm, it means that the sensor has been successfully connected to the display. In this case, the data may not be displayed due to the insufficient battery of the sensor or the unstable transmission. Then you need to replace a CR1632 battery for the sensor or consider the next step.
*Generally speaking, the signal transmission distance of the sensor is ≤36ft. If you have a repeater, the signal transmission distance will be extended to 45ft or more. However, the signal transmission will be blocked by objects and electromagnetic field interference, so the signal transmission stability and the specific transmit distance between your monitor and the sensor are determined by the actual situation on your vehicle. If you find that the signal transmission of the sensor is unstable, then it may be that the length of your vehicle has exceeded the original transmission distance of the sensor, or there are too many interference sources in your vehicle.
To remind you, this model may interfere with many reasons, for example, the smartphone, put your device not so close to your phone may help with the transmission interference.
Regarding the configuration of the repeater model, we are willing to recommend the M12-3 Blue model to you.*
2. If the alarm does not appear after removing the sensor, please back the Schrader Valve (valve core) out approximately 1/8 to 1/4 turn and reinstall the sensor. This will ensure there are sufficient contact and air pressure on the sensor. Then, drive for about 5-10 minutes to update the new pressure.
3. If the monitor still not show anything after you try the tips above, please restore your monitor to the factory settings and rematch the ID.
4. If the above suggestions do not solve your problem, please do not hesitate to get support. Please con.ta.ct us ASAP. The information is on the last page in the user manual.
--------------------------------------------------------
0 Response to "🛒 Crаzу Dеаlѕ Tymate 4-Wheel Vehicle Products TPMS Tire Pressure Monitoring System (TPMS) - Anti Theft Sensor (1 Piece)"
Post a Comment